NuTone puerta LA-204WH Manual

Manuales PDF
6 Páginas Español

NuTone puerta LA-204WH
Páginas
De
6
This device complies with RSS-210
of Industry Canada. Operation is subject
to the following two conditions: (1) this
device may not cause interference;
and (2) this device must accept any
interference, including interference
that may cause undesired operation
of the device.
Refer to Figures 1 and 2.
1. Locate the Pushbutton next to or near
the door.
Do not mount the pushbutton
on a metal surface.
2. Remove the Pushbutton cover by
inserting the tip of a screwdriver in
the slot at the bottom of the Pushbutton
and then gently rock the Pushbutton
cover apart from the Pushbutton base.
3. Choose a level place to locate the
Pushbutton base.
4. Position the Pushbutton base,
and mark the mounting surface with
a pencil through the two holes in
the Pushbutton.
5. Drill two
3
⁄16” diameter holes at
the previously marked area.
6. Insert the plastic anchors into
the
3
⁄16” diameter holes.
7. Place Pushbutton over anchors,
and fasten with two screws provided.
Do not replace cover at this time.
PUSHBUTTON SOUND CODING
Refer to Figure 3.
1. The Receiver strobe light will flash
with any chime sound selected. The
Pushbutton can be coded to sound
one of three chime sounds.
2. Select the desired sound as illustrated
in Figure 3.
3. Position the plastic jumper straps
in the proper location for desired
chime sound.
PUSHBUTTON SECURITY
CODING
Refer to Figure 3.
It is not necessary to change the
security code of the Pushbutton unless
you experience interference from other
wireless devices.
1. To change the security code, remove
any combination of the six plastic
jumper straps.
2. NOTE: Both the Pushbutton and
Receiver codes must match.
BATTERY INSTALLATION
Refer to Figure 3.
1. Position the A23 12 volt battery
as illustrated.
Be sure to observe
polarity (+/–).
INSTALLING PUSHBUTTON
COVER
Refer to Figure 4.
1. Position the Pushbutton cover over
the Pushbutton base. The red light
must be lined up over the hole in the
Pushbutton cover. Firmly press cover
over base.
INSTALLATION & OPERATING INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
Wireless Chime with Strobe Light
MODEL: LA-204WH
N
u
T
o
n
e
FIGURE 1
FIGURE 2
TO OPEN COVER
“PUSH”
SCREW HOLE FOR WALL
MOUNTING
SCREW HOLE FOR WALL
MOUNTING
+
–
6
5
4
3
2
1
ONE NOTE
TWO NOTE
WESTMINSTER
SECURITY
CODE SETTING
FIGURE 3
SOUND SELECTION
12V “A23”
BATTERY
LED
FIGURE 4
N
u
T
o
n
e
+
–
MOUNTING THE PUSHBUTTON TRANSMITTER
Manuales Relacionados para NuTone puerta LA-204WH
LA-58
Nutone puerta LA-58

Para puerta (2 Páginas)
DR-1
Nutone puerta DR-1

Para puerta (2 Páginas)
LB-46
Nutone puerta LB-46

Para puerta (2 Páginas)
LA-164
Nutone puerta LA-164

Para puerta (6 Páginas)
LA-52 Series
Nutone puerta LA-52 Series

Para puerta (12 Páginas)
LA501CY
Nutone puerta LA501CY

Para puerta (2 Páginas)
C915
Nutone puerta C915

Para puerta (2 Páginas)
LA-155GN
Nutone puerta LA-155GN

Para puerta (6 Páginas)
LA-20 SERIES
Nutone puerta LA-20 SERIES

Para puerta (2 Páginas)
LA-107
Nutone puerta LA-107

Para puerta (2 Páginas)
LA500K
Nutone puerta LA500K

Para puerta (2 Páginas)
LA-207TWH
Nutone puerta LA-207TWH

Para puerta (4 Páginas)
LA-206WH
Nutone puerta LA-206WH

Para puerta (6 Páginas)
LD-49
Nutone puerta LD-49

Para puerta (2 Páginas)
LA522WH
Nutone puerta LA522WH

Para puerta (12 Páginas)